8 (499) 391-32-03, 8 (499) 394-07-16

125363, г. Москва, ул. Новопоселковая,

д. 6, кор. 217, офис 606



ArcDev Mainliner X2 Free

The arcDev Mainliner X2 application was developed to be a triple-oscillator monosynth designed specifically for just this. Each of the 3 Osc groups is made up of three detunable suboscillators, so if you want you can quickly dial up a huge warbling chunk of hoov. Add an 8-pole LPF and 4-pole BPF, and watch the speaker cones wobble.
There’s a whole lot of modulation and wave-mangling options though, so you can get other sounds with it, too.
MLX2 is optimised for bottom-of-the-keyboard playing. It may well work as a lead-type synth, for all I know. YMMV.
Oscillator Bank
Three Oscillator groups (A/B/C), each of which is made up of three sub-oscs. Waveform for each sub-oscillator may be independently set, and suboscs may be detuned against each other.
OscGrp B & C may be set to hard-sync to, or be frequency-modulated by, subosc 1 of OscGrp A. If either oscgrp is set to FM, OscGrp A main output is muted, and its LVL control is re-routed to adjust FM Depth.
Additionally, OscGrps B & C are sent through an adjustable-level Ring Modulator. Standard White-noise generator is also present.
Filter Bank
Two independent filters. Filter A is switchable 4pole / 6pole / 8pole Low-Pass. Filter B is switchable 2pole / 4pole Band-Pass or High-Pass.
Filter routing may be switched between three modes:
— Parallel
Signal passes seperately through Filters A & B.
Mix controls A/B Mix.
— Multi
Signal passes though Filter A, then is split — one signal passes to the output, while the other passes through Filter B.
Mix controls A/A+B mix.
— Serial
Signal passes through Filter A, then Filter B. Mix is disabled.
Envelope Generators
Four velocity-sensitive (H)ADSR generators. Env A is hardwired to main amplitude, Env B is hardwired to Filter A Cutoff. Env B & C can be freely assigned to most parameters.
Env B, C & D feature adjustable Pre-Hold (delay) time & bipolar velocity and mod depth. Env A features unipolar velocity.

Lfo Generators
Three tempo-syncable assignable Lfo generators.
Smooth/Quantize control modifies Lfo wave shape:
Negative values smooth sharp transitions (useful for smoothing out a random waveform).
Positive values quantise smooth transitions (useful for ‘stepping’ a sine or triangle waveform).







ArcDev Mainliner X2 Activation Code Free For PC

Based on a formidable (!) sequencer!
Intuitive navigation with joystick — little buttons.
Drag and drop on the score to add or rename sections or change a parameter name (this is an overlay for the score editor, and can also be used for keyboard playing).
Saving and Load on a song.
Segmentation — notes can be delineated into non-overlapping sections with the use of a midi note (specifically a C0 midi Note) which can have its name defined as a section name.
Comprehensive set of oscillator and filter parameters.
Easy construction of any patch.
Create snapshots of your music and store in an array of.ogg files.
Separated LFO paths
Stereo arpeggiator
4-pole Low-pass / 6-pole band-pass or 8-pole high-pass filter
Modulation options
Ring modulation
Syncable modulation from other modules.
Generic Noise generator
Damped Rate controller
Korg-style arpeggiator
Cyclic (Random) arpeggiator
Segmented Arbitrary arpeggiator
Chord generator
MIDI Learn (small)
MIDI Learn (large)
MIDI Learn (lock)
MIDI Learn (unlock)
MIDI Learn (solo)
MIDI Learn (auto)
MIDI Learn (soft)
MIDI Learn (hard)
MIDI Learn (legacy)
MIDI Learn (soft bypass)
MIDI Learn (hard bypass)
MIDI Learn (lock)
MIDI Learn (unlock)
MIDI Learn (solo)
MIDI Learn (auto)
MIDI Learn (soft)
MIDI Learn (hard)
MIDI Learn (legacy)
MIDI Learn (soft bypass)
MIDI Learn (hard bypass)
MIDI Learn (lock)
MIDI Learn (unlock)
MIDI Learn (solo)
MIDI Learn (auto)
MIDI Learn (soft)
MIDI Learn (hard)
MIDI Learn (legacy)
MIDI Learn (soft bypass)
MIDI Learn (hard bypass)
MIDI Learn (lock)
MIDI Learn (unlock)
MIDI Learn (solo)

ArcDev Mainliner X2 (Latest)

Mainliner X2 is an easy-to-use, inexpensive synthesizer. More than just a sampler, it can make funny, spacey sounds.
With its unique oscillators, modulation options, and LFOs, you’ll find tons of expression. And the coolest feature is that it «locks» to arpeggio sequences. So it’s easy to generate crazy, complex arpeggios.
Mainliner X2 can be played just like an arpeggiator, or it can be turned into a variety of weird, spacey sounds. All switches and controls are all conveniently located in the front panel.
The MLX2 features two VCF/VCF+LFOs, two VCAs, two rotary potentiometers, a switchable 4-pole lowpass filter, and an LFO. A summing/comparator mixer, coupled with two clean LFOs, can be used as a multi-mode lfo subtractor. (Example: +3 / f = +2/fa, +4 / f = +2/fb, +5/f = +3/fb, +6/f = +5/fb, making for a varying clean, saw-like osc.)
There’s also a highly customizable arpeggiator, with click-chorus and any arpeggio you can imagine. There’s even an LFO arpeggiator mode that will turn your arpeggiator into an LFO for each arpeggio. There are also 7 different arpeggio patterns available.
So make up your own crazy arpeggios, and then modulate these arpeggios into any of the oscs, filters, LFOs and CV/Gate.
VCO/VCF, VCF/VCF+LFO, Phase Shifter/Phase Shifter+LFO, ADSR envelope generators, 2 oscillator groups, 2 LFOs, 2 VCAs, 4 pole / 6 pole filters, Envelope Generator, LFO, RMI, Arpeggiator, XLR input, S/H, MS, MM, [3] different arpeggio patterns, Easy access to controls and switches (front panel), True portamento, sample rate at 44.1 kHz, 12 bit 
controls, ar

ArcDev Mainliner X2

Designed specifically for the old Yamaha M’Bass MB303, the MB303 clone is a monosynth with a rather limited feature set, although obviously designed to run on a simple two-op op-amp based circuit. It uses two oscillators which are frequency modulated against each other, using three envelope generators, two ADSR sequencer-ops, two sequencer LFO’s and a simple power input circuit. All of which can be controlled from a single on/off slider on the control panel.
It’s a monosynth based on the DIY concept of «build yourself a low-level 2nd-generation monosynth at a fraction of the cost!». You can give it a few on/offs, a few pots and a couple of button banks, and it will generate a few different sounds.
The user guide describes the synth very well. Although these notes are generally about all the features, they don’t cover the full device.
The sequencer allows you to arrange any number of running sequences together (in one layer, or in groups) and to select combinations (knobs) of notes and chords from your keyboard to form chords or patterns. The sequences are set for display on the control panel, with their duration markers.
The sequencer also has a’slicer’ mode to display a 3-octave-per-voice view of the sequencer to help you ‘place’ notes in your playing.
Each layer of the sequencer also has an optional arpeggiator function.
If you need a monosynth with a more definied, commercial tone, check out our Ubersynth Lite or Pro.
Among other things, X2 generates quirky-sounding continuous, continuous plus, sustain plus, monophonic pitch-shifted and up/down pitched quantised tones.
Shelf 3 is an All Lead-type monophonic custom-designed synth.
The combination of 3 oscillators, 2 filters, 6 LFO’s, 9 envelopes, a sequencer, a slicer, a modulator, etc. give you a lot of flexibility. Shelf 3 has a long, very resonant sustain.
Shelf 3 is great for leads in minimal or empty space.
If you want a piano-type synth with more tonal variety and a flatter envelope, check out the MIDI-Ubersynth.
After completing a tutorial, you will have a good idea of how to use a

What’s New in the ArcDev Mainliner X2?

Defined by the combination of a great list of oscillators, and their awesome capabilities. The Mainliner X2 has a «creamy» voice to it, which allows it to be used effectively as a bass synth, although most people would likely think of it as a lead or midrange. A few times out of ten it will sing its a capella best, and you might think of it as a single lead synth that happens to have some interesting oscillators thrown in.
The preset «creamy» voice was created for the purpose of being a lead synth, and it’s certainly capable of most of the more complicated kinds of lead sounds that people make. But the main oscillators, especially the MSBs, are quite capable of producing some of the bassier tones that the x2 is capable of.
So if you want some funk, or some bass, or even some lead, you can get all of that.
The Mainliner x2 also features some pretty awesome unusual functions. If you want to go nuts, you can most definitely use the main oscillators to make music with an absolute gamut of tones to play with. But the thing that really sets the Mainliner apart from other synths is the fact that you can get some pretty unique/funky sounds just by increasing/decreasing the amplitude of the lower oscillators.
The filters are some of the most versatile filters that you will find in any synth, and the ring modulator is fast and responsive, and adds a whole new dimension to your sound.
The LFO has all the options you would hope for from such a feature, and the envelope generators are simply marvelous. They can be controlled by modulating the oscillators directly, or by using the nice velocity controls. They are also, just as they are, absolutely programmable, meaning you can create any complex setting to create any sort of waveform.
The Mainliner X2 features all sorts of knobs and switches to control various parameters, such as the oscillator waveforms, filters, ring modulator, LFO, filters, and more. Each of the oscillator sets have their own set of parameters, including controls for the waveforms (the MOSBs, the MSBs, the MSB-MSB and the LSBs, the RSCs, etc.), the detune of the MSBs, the mod depth, and the RSC mod waveform. All of the filter controls are also independent of each other, allowing all of the filter


System Requirements For ArcDev Mainliner X2:

* Your computer’s processor must be a 64-bit compatible machine.
* Please install DirectX 9.0 or higher in order to use this game.
* The system must meet the conditions below to be able to use this game.
HD Model X14HD Model F10HD Model F20HD Model F30HD Model X20HD Model X30
CPU: Intel Core i5-2500K(4.2GHz), AMD Phenom II X4 965 (3.4GHz)
GPU: NVIDIA GeForce GTX 690,


Sorry, comments are closed for this post.